Buy Saeyang Marathon K35 / SH30N milling machine wholesale and retail in ubeauty.pro store

To maintain the status of a successful nail service master, everyone chooses his own specific strategy for himself.

Nevertheless, there is still one universal "trick" that suits everyone and will undoubtedly help increase your chances of achieving leadership positions in this type of activity.

Agree that clients create their first opinion about any master of their craft by visually determining his level as a specialist. Does he look good, how neat is he, and most importantly, what is the quality and level of his equipment.

We conclude: in addition to the skills of communicating with people, high qualifications and sterile cleanliness, the necessary condition is that the first and, most importantly , customers received a positive impression already at the first glance at your workplace. Thus, you need not only a high-quality and powerful, but also a memorable and unusual device for manicure procedures.

And one of the devices that combines these qualities, and which, at the first glance, will successfully distinguish you among Saeyang Marathon K35/SH30N will undoubtedly become colleagues.

This kit consists of a slightly unusual, miniature, but at the same time very high-quality and practical SH30N micromotor handle and an improved Marathon K35 control unit. Their union certainly makes this set the undoubted leader and one of the brightest Saeyang devices.

The snow-white plastic case of the unit has the shape of a parallelepiped with sides of 11.5x11.5x7 cm. On its front side there is a screen with a digital speed indication rotation, a speed control knob, a connector for connecting a micromotor handle and two membrane buttons (one switches the rotation of the handle to reverse, and the second controls the hand / pedal unit). The on/off button is located on the side.

There are seven holes on the upper part of the body for installing the cutters necessary for this procedure. There are two connectors on the back of the body for connecting pedals:

1. large, similar to a pen connector, used to connect a variable pedal,

2. significantly smaller one is designed to connect a pedal that operates on/off the handle.

But the main "highlights" of this interesting device is that it has a "feedback" function. It is also equipped with a microprocessor and has adopted an electronic overload protection system for the handle and block.

The "feedback" function allows the master during work not to worry that the handle may "burn out" or not "pull" one procedure or another. After all, if you work with a handle with a load, then taking into account all the parameters, the microprocessor will add current in a split second. After that, you can continue to work with the same effort - neither the speed of the handle, nor its torque will change. If there is a prolonged excessive overload, the processor will simply disconnect the handle from power to draw your attention to this.

Another convenient feature is the ability to switch the direction of rotation while the handle is running, because in most cases it is categorical to do this it is forbidden. In this case, this is possible due to the fact that the K35 uses an improved special circuit.

It is also worth noting that the control unit provides protection against jamming of the handle in case you forgot to install the cutter and turned on the machine in this condition. Usually such an oversight can lead to serious damage to the handle, up to and including jamming without the ability to open the collet again. But if this happens with the Marathon K35 block, then it will recognize the error and simply will not supply current to the handle. In this case, the display will show an error code, and the LEDs on the front panel will flash red, which will also indicate a mistake.

This electronic control unit has certainly received one of the most elegant pens as a "girlfriend".

As for the technical characteristics that this beautiful micromotor handle received from engineers, it meets all modern hygiene and safety requirements. The main part of the case, inside which a 45 W micromotor is located on high-speed bearings, is made of high-quality steel-colored plastic. It is thanks to the presence of bearings that the handle makes practically no noise during operation, and it has no radial runout. And the micromotor itself has the ability to reach a maximum speed of up to 30,000 rpm.

The second half of the body in the place where it is held by the fingers is made of metal and has a diameter of only 12 mm. And this is with a handle length of only 129 mm and 160 g of weight, which certainly adds to its elegance. But this technical feature has its big plus - a large area of the metal surface allows you to give the environment much more heat from the bearings that heat up during operation. Also, the handle has a radial technical hole in the rear part for forced airflow of the body during operation, and this also facilitates the cooling of the micromotor.

But the most important parameter of the micromotor is a torque of 2.9 N cm, which, thanks to the function of the "feedback" block is preserved during operation at any speed. And the presence of a standard "Twist-Lock" type collet will reduce the time for changing nozzles to 1-2 seconds.

An important detail: although the handle is made to serve customers on the stream, it is advisable to do a pedicure with it no more than 1- 2 times a day.