Buy Kit for fog formation 10m. 10 nozzles 0.3 mm. with pump. White. wholesale and retail in ubeauty.pro store

Quick kit for fogging system.

Contents:

Connecting plastic food tube 10 meters. The color is white.

Tees 10pcs

Injectors nozzle diameter 0.3mm. 10pcs

1/2' thread adapter

Working range 3-15 atmospheres.

Pressure pump.

Pump equipped with a pressure sensor, to switch off when reaching maximum pressure, very effective when using intermediate receiver, on-off control timer.

Rubber anti-vibration feet to reduce noise and vibration.

12V power supply required. at least 7A.

Voltage: 12VDC

Max Power: 80W

Connection: 1/2' BSP male

Working pressure: 5.5 bar

Maximum pressure: 9 bar

Suction Depth: 1.5m

Water Height: 55m

flow (max): 330L/h

Size: 165x95x60mm

Filter as pictured additional option if needed.

Approximate fluid flow at a pressure of 5 atm. depends on nozzle diameter

0.2mm - 25gr. min

0.3mm - 45gr. min

0.4mm - 87gr. min

0.5mm - 155gr. min

0.6mm - 290gr. min

Much more durable than brass and plastic nozzles tick.

The nozzles are equipped with a shut-off valve that closes when the pressure decreases and thus prevents the liquid in the tube from flowing out.

Misting systems with low pressure nozzles are a convenient and inexpensive way to increase comfort, reduce air temperature, increase humidity, etc.

You don't need expensive tools or special skills to mount it.

Stainless steel collapsible nozzles with valve system are used.

When turn off the fluid supply and reduce the pressure the nozzles are closed with a valve and the liquid remaining in the tubes does not drain through the bottom nozzles.

The ceramic inlay greatly extends the lifespan.

When If necessary, the nozzles are easily removed and disassembled for cleaning or removing calcified deposits by soaking in vinegar or other suitable liquid.

Applies to:

Cafes and Restaurants - Reduce Temperature, Increase Comfort Zone

Verandahs and Recreation Areas - Dust control, temperature reduction, humidity increase

Cottages and apartments - fighting dust, lowering temperatures, increasing humidity

Production facilities, warehouses, printing houses, incubators, etc.

Greenhouses - cooling, increasing humidity, micro fertilizer and other substances

Storing vegetables - keeps fresh look and nutrients for a long time

and mosquitoes really don't like wet environments, avoid such areas

Suppression of odors and dust, dust when combined with micro water drops becomes heavy and settles

Can be connected as normal plumbing with sufficient pressure or pressurize with a suitable pump.

It is recommended to use a mechanical water prefilter to avoid nozzle clogging. When using water with a high content of dissolved salts, hard water, calcification of holes and poor performance may occur.

Manual control possible, open-closed.

Management with a cyclic timer, constant work in cycles, work-pause mode will depend on the set values and depend on the capabilities of the timer.

Relay control time, this is when you need not constant work, but switching on at certain hours, days, or phases of the day.

Moisture sensor control, triggered by desired humidity values set.

Combination of control sensors is also possible for more complex tasks.

At high pressure and small nozzle diameter, the liquid flow is scattered into micro drops, 5 microns in size. Due to the large total area, rapid evaporation occurs. This process is also called thermodynamic. Its effectiveness is explained by the fact that it takes a lot of energy to evaporate water - evaporation of 1 ml of water occurs at the cost of 500-600 calories of heat.

Water evaporation process underlying fogging systems , strongly depends on two factors: 1. Ambient air temperature, 2. Relative air humidity, i.e. the drier and hotter the higher the efficiency of the system. At high temperatures and low humidity, the temperature can drop by up to 15 degrees. It should not be forgotten that fogging systems humidify dry summer air, reduce dust and remove unwanted odors, which greatly facilitates breathing. Thus, fogging systems should be considered not as a conventional cooling system, but more as a system for creating and maintaining a comfortable microclimate on the given territory.

The microclimate created by the fogging system has a beneficial effect on human health, especially in broncho-pulmonary diseases, diseases of the cardiovascular system, allergies, neuroses, etc.